Bill Porter GND GND VCC VCC DAT GND VCC TX RX ESPixel No Warranty Expressed or Implied RevC Short for 5V <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find resistors, capacitors, inductors, test points, jumper pads, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. This is the "EZ" version of the .1" spaced ceramic thru-hole cap. It has reduced top mask to make it harder to put the component on the wrong side of the board. >Name >Value >Name >Value <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find connectors and sockets- basically anything that can be plugged into or onto. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. This footprint was designed to help hold the alignment of a through-hole component (i.e. 6-pin header) while soldering it into place. You may notice that each hole has been shifted either up or down by 0.005 of an inch from it's more standard position (which is a perfectly straight line). This slight alteration caused the pins (the squares in the middle) to touch the edges of the holes. Because they are alternating, it causes a "brace" to hold the component in place. 0.005 has proven to be the perfect amount of "off-center" position when using our standard breakaway headers. Although looks a little odd when you look at the bare footprint, once you have a header in there, the alteration is very hard to notice. Also, if you push a header all the way into place, it is covered up entirely on the bottom side. This idea of altering the position of holes to aid alignment will be further integrated into the Sparkfun Library for other footprints. It can help hold any component with 3 or more connection pins. >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find drivers, regulators, and amplifiers. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find resistors, capacitors, inductors, test points, jumper pads, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. This is the "EZ" version of the standard .3" spaced resistor package. It has a reduced top mask to make it harder to install upside-down. >Name >Value <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find all manner of retired footprints for resistors, capacitors, board names, ICs, etc., that are no longer used in our catalog. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing:Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. OMRON SWITCH >NAME <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find discrete semiconductors- transistors, diodes, TRIACs, optoisolators, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. TO 92 >NAME >VALUE Diodes Based on the following sources: <ul> <li>Motorola : www.onsemi.com <li>Fairchild : www.fairchildsemi.com <li>Philips : www.semiconductors.com <li>Vishay : www.vishay.de </ul> <author>Created by librarian@cadsoft.de</author> DIODE diameter 2 mm, horizontal, grid 7.62 mm >NAME >VALUE Linear Devices Operational amplifiers, comparators, voltage regulators, ADCs, DACs, etc. <author>Created by librarian@cadsoft.de</author> TO-92 >NAME >VALUE EAGLE Design Rules Die Standard-Design-Rules sind so gewÃ¤hlt, dass sie fÃ¼r die meisten Anwendungen passen. Sollte ihre Platine besondere Anforderungen haben, treffen Sie die erforderlichen Einstellungen hier und speichern die Design Rules unter einem neuen Namen ab. Laen's PCB Order Design Rules Please make sure your boards conform to these design rules. Since Version 6.2.2 text objects can contain more than one line, which will not be processed correctly with this version.